Slide background




ISO 16092-2:2019 Sicurezza Presse meccaniche

ID 9443 | | Visite: 4443 | Documenti ISOPermalink: https://www.certifico.com/id/9443

ISO 16092 2 2019

ISO 16092-2:2019 Sicurezza Presse meccaniche

Machine tools safety - Presses - Part 2: Safety requirement for mechanical presses

Introduction

This document is a type-C standard as stated in ISO 12100.
 
This document is of relevance, in particular, for the following stakeholder groups representing the market players with regard to machinery safety:

- machine manufacturers (small, medium and large enterprises);
- health and safety bodies (regulators, accident prevention organisations, market surveillance etc.)

Others can be affected by the level of machinery safety achieved with the means of the document by the above-mentioned stakeholder groups:

- machine users/employers (small, medium and large enterprises);
- machine users/employees (e.g. trade unions, organizations for people with special needs);
- service providers, e. g. for maintenance (small, medium and large enterprises);
- consumers (in case of machinery intended for use by consumers).

The above-mentioned stakeholder groups have been given the possibility to participate at the drafting process of this document.
The machinery concerned and the extent to which hazards, hazardous situations or hazardous events are covered are indicated in the Scope of this document.
When requirements of this type-C standard are different from those which are stated in type-A or type-B standards, the requirements of this type-C standard take precedence over the requirements of the other standards for machines that have been designed and built according to the requirements of this type-C standard.
 
Scope
 
This document, in addition to ISO 16092-1, specifies technical safety requirements and measures to be adopted by persons undertaking the design, manufacture and supply of the following groups of mechanical presses and mechanical press production systems:
 
- Group 1: Presses with a part revolution clutch(es);
- Group 2: Presses with a servo drive system (Mechanical servo presses).

NOTE 1 
Requirements in this document are essentially applicable to both groups of the mechanical press. If a requirement applies to only one group, then the group is specified.

NOTE 2 
Other types of motorized drive systems provide similar functionalities to what is commonly called “servo drives” or "servo motors”, and as such their use is considered the same within the terms used in this document (e.g. variable frequency drive systems).

The presses covered by this document range in size from small high-speed machines with a single operator producing small workpieces to large relatively slow-speed machines with several operators and large complex workpieces.
This document deals with all significant hazards relevant to mechanical presses and ancillary devices (e.g. moving die cushions, work-piece ejectors, feeding and transfer systems) which are integral to the machine, when they are used as intended and under the conditions of misuse which are reasonably foreseeable by the manufacturer (see Clause 4). All phases of the machine life cycle as described in ISO 12100:2010, 5.4 have been taken into consideration.

NOTE 2 All significant hazards means those identified or associated with presses at the time of the publication of this document.

In addition to machines not covered by ISO 16092-1:2017, this document does not cover machines which:

a) transmit energy to impart press slide motion by using hydraulic or pneumatic means;
b) have two or more slides moving in different angular orientations from each other;

NOTE 3 
This document applies to presses which have two or more slides moving in the same angular orientations, e.g. a press which has inner and outer slides.


c) transmit energy to impart press slide motion by using a linear motor mechanism(s).
 

Tags: Normazione Norme ISO

Articoli correlati

Ultimi archiviati Normazione

Set 26, 2023 292

CEI 0-16, V2:2023-06

CEI 0-16, V2:2023-06 ID 20471 | 26.09.2023 / Variante V3:2023 Questa Norma costituisce la Variante V2 della Norma CEI 0-16:2022-03, ed è costituita dal solo Allegato T “Scambio informativo basato su standard IEC 61850” in versione consolidata come risultante dell’Allegato T della Norma CEI… Leggi tutto
Set 22, 2023 431

UNI 11911:2023

UNI 11911:2023 / Qualificazione stabilimenti balneari ID 20451 | 22.09.2023 UNI 11911:2023Stabilimenti balneari - Requisiti e raccomandazioni per l'esercizio dell'attività - Elementi di qualificazione Data disponibilità: 21 settembre 2023 _______ La norma fornisce agli operatori del settore… Leggi tutto
Decisione di esecuzione  UE  2023 1759
Set 12, 2023 1088

Decisione di esecuzione (UE) 2023/1759

Decisione di esecuzione (UE) 2023/1759 / Norme armonizzate per le lavastoviglie per uso domestico 09.2023 ID 20381 | 12.09.2023 Decisione di esecuzione (UE) 2023/1759 della Commissione dell'11 settembre 2023 relativa alle norme armonizzate per le lavastoviglie per uso domestico elaborate a sostegno… Leggi tutto
Set 11, 2023 1089

UNI 11764:2019

UNI 11764:2019 / Requisiti di prova piccoli trabattelli ID 20376 | 11.09.2023 / In allegato Preview Piccoli trabattelli su due ruote - Requisiti e metodi di prova La norma specifica i requisiti e i metodi di prova dei piccoli trabattelli su due ruote con l'altezza del piano di lavoro minore di 4 m… Leggi tutto

Più letti Normazione