Informazione tecnica HSE / 25 ° anno

Sicurezza
Guide INAIL
Ambiente
Guide ISPRA
Chemicals
Guide ECHA
Marcatura CE
Guide CE
Prevenzione Incendi
Guide PI
Merci Pericolose
Radiazioni ionizzanti
Direttiva macchine
HACCP
Impianti
Trasporto
Normazione
Costruzioni
Featured

ISO 20607:2019 Safety of machinery Instruction handbook

ID 8678 Visite: 11343 Documenti ISO
3 allegati

ISO 20607 2019

ISO 20607:2019 Safety of machinery Instruction handbook

Safety of machinery - Instruction handbook - General drafting principles

Vedi Documento ISO 20607:2019 IT

1a Ed. June 2019 Preview in allegato (documento di approfondimento in elaborazione | Richiedi interesse)

This document specifies requirements for the machine manufacturer for preparation of the safety-relevant parts of an instruction handbook for machinery.

This document:
- provides further specifications to the general requirements on information for use given in ISO 12100:2010, 6.4.5; and
- deals with the safety-related content, the corresponding structure and presentation of the instruction handbook, taking into account all phases of the life cycle of the machine.

NOTE 1 The strategy for risk reduction at the machine is given in ISO 12100:2010, Clause 6, and includes inherently safe design measures, safeguarding and complementary risk reduction measures as well as information for use.

NOTE 2 Annex A contains a correspondence table between ISO 12100:2010, 6.4, and this document.

NOTE 3 Information for conception and preparation of instructions in general is available in IEC/IEEE 82079-1. This document establishes the principles which are indispensable to provide information on residual risks. This document does not address requirements for declaration of noise and vibration emissions. This document is not applicable to machinery manufactured before the date of its publication.

______

Foreword

ISO (the International Organization for Standardization) is a worldwide federation of national standards bodies (ISO member bodies). The work of preparing International Standards is normally carried out through ISO technical committees. Each member body interested in a subject for which a technical committee has been established has the right to be represented on that committee. International organizations, governmental and non-governmental, in liaison with ISO, also take part in the work. ISO collaborates closely with the International Electrotechnical Commission (IEC) on all matters of electrotechnical standardization.

The procedures used to develop this document and those intended for its further maintenance are described in the ISO/IEC Directives, Part 1. In particular, the different approval criteria needed for the different types of ISO documents should be noted. This document was drafted in accordance with the editorial rules of the ISO/IEC Directives, Part 2 (see www.iso.org/directives).
Attention is drawn to the possibility that some of the elements of this document may be the subject of patent rights. ISO shall not be held responsible for identifying any or all such patent rights. Details of any patent rights identified during the development of the document will be in the Introduction and/or on the ISO list of patent declarations received (see www.iso.org/patents).
Any trade name used in this document is information given for the convenience of users and does not constitute an endorsement.

For an explanation of the voluntary nature of standards, the meaning of ISO specific terms and expressions related to conformity assessment, as well as information about ISO's adherence to the World Trade Organization (WTO) principles in the Technical Barriers to Trade (TBT) see www.iso.org/iso/foreword.html.

This document was prepared by Technical Committee ISO/TC 199, Safety of machinery.
Any feedback or questions on this document should be directed to the user’s national standards body. A complete listing of these bodies can be found at www.iso.org/members.html.

Introduction

This document is a type-B standard as stated in ISO 12100.
This document is of relevance, in particular, for the following stakeholder groups representing the market players with regard to machinery safety:

- machine manufacturers (small, medium and large enterprises);
- health and safety bodies (regulators, accident prevention organisations, market surveillance etc.).

Others can be affected by the level of machinery safety achieved with the means of the document by the above-mentioned stakeholder groups:

- machine users/employers (small, medium and large enterprises);
- machine users/employees (e.g. trade unions, organizations for people with special needs);
- service providers, e. g. for maintenance (small, medium and large enterprises);
- consumers (in case of machinery intended for use by consumers).

The above-mentioned stakeholder groups have been given the possibility to participate at the drafting process of this document.
In addition, this document is intended for standardization bodies elaborating type-C standards.
The requirements of this document can be supplemented or modified by a type-C standard.

For machines which are covered by the scope of a type-C standard and which have been designed and built according to the requirements of that standard, the requirements of that type-C standard take precedence.

Preview in attacchment
 
Vedi Documento ISO 20607:2019 IT
 
 
Allegati (Riservati) Abbonati Normazione
Descrizione Lingua Dimensioni Downloads
Scarica il file (EN ISO 12100 Redigere il Manuale di Istruzioni - Estratto 6.4.5)
EN ISO 12100 Redigere il Manuale di Istruzioni - Estratto 6.4.5
Certifico Srl - Rev. 0.0 2017
Abbonati Normazione
IT 80 kB 73
Scarica il file (ISO 20607 2019 EN Preview)
ISO 20607 2019 EN Preview
ISO 2019
Abbonati Normazione
IT 1105 kB 52
Allegati
Descrizione Lingua Dimensioni Downloads
Scarica il file (ISO 20607 2019 EN Licensed Certifico)
ISO 20607 2019 EN Licensed Certifico
ISO 2019
IT 209 kB 1910

Articoli correlati Normazione

Documenti Riservati Normazione
Modello relazione utilizzo vita residua apparecchio di sollevamento Rev 00 2022

Modello relazione utilizzo-vita residua (anche a supporto indagine supplementare) apparecchio di sollevamento / ISO 4301-1

ID 17786 | 08.10.2022 / Documento completo in allegato formato doc/pdf

Modello...

Documenti Riservati Normazione
UNI EN 13374 2019

UNI EN 13374:2019 | Sistemi temporanei di protezione dei bordi 

Sistemi temporanei di protezione dei bordi - Specifica di prodotto - Metodi di prova

Data entrata in vigore: 07 marzo 2019

La norma specifi...

Norme armonizzate BT Bassa Tensione
Norme armonizzate LV

Decisione di esecuzione (UE) 2023/600 / Norme armonizzate BT Marzo 2023

ID 19225 | 17.03.2023

Decisione di esecuzione (UE) 2023/600 della Commissione del 13 marzo 2023 che modifica la decisione di esec...

Certifico s.r.l.

Sede: Via A. De Curtis, 28 - 06135 Perugia - IT
Sede: Via Madonna Alta 138/A - 06128 Perugia - IT
P. IVA: IT02442650541

Tel. 1: +39 075 599 73 63
Tel. 2: +39 075 599 73 43

Assistenza: 800 14 47 46

www.certifico.com
info@certifico.com

Testata editoriale iscritta al n. 22/2024 del registro periodici della cancelleria del Tribunale di Perugia in data 19.11.2024

Info

Marketing

Utilities

Policies

Store

Social

Media